Pro1.pl | See the cheapest prices and offers on !URL

Advanced GOM-002-D1 - GO1 Spare Door

Advanced GOM-002-D1 - GO1 Spare DoorAdvanced GOM-002-D1 is a spare door designed for use with the G01 series. If you require more information please do not hesitate to contact us.

GBP 81.97

1

Carrier DC408 Industrial Floor Mount Contact For Garage Door High Security Grade 3 Grey

Carrier DC408 Industrial Floor Mount Contact For Garage Door High Security Grade 3 GreyThe grade 3 magnetic contacts are high security contacts which do meet the following requirements preciseness of opening distance magnet polarisation strength of the magnet.Key FeaturesEN 50131-2-6 Grade 3 and VDS certified2m cableTamper protected

GBP 64.84

1

Global Fire Valkyrie ASB Addressable Red Wall Sounder Beacon

Global Fire Valkyrie ASB Addressable Red Wall Sounder BeaconThe VALKYRIE ASB is a Wall Mounted Addressable Sounder Beacon with low power consumption. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch. Four different tones are available and selected using DIL switches 6 and 7.When individual address reporting is not required VALKYRIE AS can be configured as a Shadow Sounder. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.

GBP 50.54

1

Global Fire Equipment VALKYRIE-ASBLK Valkyrie AS Addressable Wall Sounder - Black

Global Fire Equipment VALKYRIE-ASBLK Valkyrie AS Addressable Wall Sounder - BlackThe VALKYRIE AS is a Wall Mounted Addressable Sounder with low power consumption. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch. Four different tones are available and selected using DIL switches 6 and 7.When individual address reporting is not required VALKYRIE AS can be configured as a Shadow Sounder. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.Key FeaturesColour Black

GBP 56.87

1

Global Fire Valkyrie ASI IP65 Addressable Red Sounder with Isolator

Global Fire Valkyrie ASI IP65 Addressable Red Sounder with IsolatorThe VALKYRIE AS IP65 is a Wall Mounted Addressable Sounder with low power consumption. It is specifically designed to be used outdoors. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8 way DIL switch. Four different tones are available and selected using DIL switches 6 and 7.When individual address reporting is not required VALKYRIE AS IP65 can be configured as a Shadow Sounder. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.

GBP 65.70

1

Global Fire Valkyrie ASBI IP65 Addressable Red Sounder Beacon with Isolator

Global Fire Valkyrie ASBI IP65 Addressable Red Sounder Beacon with IsolatorThe VALKYRIE AS IP65 is a Wall Mounted Addressable Sounder Beacon with low power consumption. It is specifically designed to be used outdoors. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8 way DIL switch. Four different tones are available and selected using DIL switches 6 and 7. When individual address reporting is not required VALKYRIE AS IP65 can be configured as a Shadow Sounder.In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.

GBP 78.34

1

RGL Electronics 24048TRS Switchmode PSU - 24VDC Regulated Output

RGL Electronics 24048TRS Switchmode PSU - 24VDC Regulated OutputThe 24048TRS is a 24V DC 8-way power supply. Ideal for fire systems hold door open magnets and 24 Volt systems that do not require battery backup.Key FeaturesIdeal for hold door open magnetsOutput released on fire alarm activationNot for use with back up batteryFull current to loadLED indicatorsShort circuit protectionTechnical Specifications24V DC regulated output4 Amp 8-way PSU

GBP 63.38

1

Carrier DC408R4.7 Floor Mount Roller Shutter Contact 2m Armoured Cable

Carrier DC408R4.7 Floor Mount Roller Shutter Contact 2m Armoured CableFloor mount roller shutter contact 2M armoured cable NC 34mm gap 4K7 resistors Grade 3 and Vds C approvedThe grade 3 magnetic contacts are high security contacts which do meet the following requirements preciseness of opening distance magnet polarisation strength of the magnet.Key FeaturesEN 50131-2-6 Grade 3 and VDS certified2m cableTamper protectedBuilt in 4k7 EOL resistor

GBP 64.84

1

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with Isolator

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with IsolatorThe VALKYRIE ABI IP65 is a Wall Mounted Addressable Beacon with Isolator and low power consumption. It is specifically designed to be used outdoors. Up to 32 individually addressed beacons can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8 way DIL switch.When individual address reporting is not required VALKYRIE ABI IP65 can be configured as a Shadow Beacon. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow beacons do not report back to the control panel so their presence on the loop is not monitored.Shadow beacons draw current from the loop 3 mA in alarm and must be included in loop load calculations. These units are produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.

GBP 65.70

1

Global Fire VALKYRIE-ASBWHT VALKYRIE Addressable Wall Mount Sounder Beacon White

Global Fire VALKYRIE-ASBWHT VALKYRIE Addressable Wall Mount Sounder Beacon WhiteThe VALKYRIE range is from Global Fire and is an addressable wall mount sounder Beacon in the colour whiteThe VALKYRIE ASB is a Wall Mounted Addressable Sounder Beacon with low power consumption. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch. Four different tones are available and selected using DIL switches 6 and 7.When individual address reporting is not required VALKYRIE AS can be configured as a Shadow Sounder. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.

GBP 50.54

1

Global Fire VALKYRIE-ASBBLK VALKYRIE Addressable Wall Mount Sounder Beacon Black

Global Fire VALKYRIE-ASBBLK VALKYRIE Addressable Wall Mount Sounder Beacon BlackThe VALKYRIE range is from Global Fire and is an addressable wall mount sounder Beacon in the colour Black.The VALKYRIE ASB is a Wall Mounted Addressable Sounder Beacon with low power consumption. Up to 32 individually addressed sounders can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch. Four different tones are available and selected using DIL switches 6 and 7.When individual address reporting is not required VALKYRIE AS can be configured as a Shadow Sounder. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow sounders do not report back to the control panel so their presence on the loop is not monitored. Shadow sounders draw current from the loop 10 mA in alarm and must be included in loop load calculations.Key FeaturesColour Black

GBP 75.82

1

RGL Electronics 24024TRS Switchmode PSU - 24VDC Regulated Output

RGL Electronics 24024TRS Switchmode PSU - 24VDC Regulated OutputThe 24024TRS is a 24V DC 4-way power supply. Ideal for fire systems hold door open magnets and 24 Volt systems that do not require battery backup.Key FeaturesSwitchmode technologyMild steel constructionWhite powder coatedMultiple cable entryCable retention pointsTechnical SpecificationsIdeal for hold open magnets and door closers2 Amp 4 way PSUOutput can be fail-safe or fail-secureDual inputs external voltage or volt freeNot for use with back up batteryFull current to load24-26VDC REGULATED outputLED Indicators for OP fault mainsShort circuit protectionFused outputBack EMF protection

GBP 47.54

1

Apollo 45681-330APO Intelligent Sounder Visual Indicator Base with Isolator

Apollo 45681-330APO Intelligent Sounder Visual Indicator Base with IsolatorThe low volume range is useful in areas such as hospitals where a fire alert is initially intended to warn staff only. The sounder is set to the high range for general use. Synchronisation of tones ensures the integrity of the signaltones from different sounders do not merge into one signal that could be mistaken for a different tone. Group addressing is a simple method of alerting an entire area or group of rooms without delay.For systems requiring isolators at every point the built-in isolator saves installation time and cost. The acoustic self-test means that the sounder listens to itself when it is switched on. If no sound is detected a fault signal is transmitted when the sounder is polled.The beacon self-test is achieved by means of an LED monitoring circuit. If the LEDs do not draw current when the sounder beacon base has been switched on a fault signal is transmitted when the device is next polled.Key FeaturesTwo volume ranges 55-75dBA and 75-91dBAVisual indicator flash rate of once per secondSynchronisation of alert and evacuate tonesSynchronisation of visual indicator flashIndividual and group addressingUnique acoustic and visual indicator self-testBuilt-in Isolator

GBP 58.67

1

Vimpex VPSU-24-02A Boxed 24Vdc Power Supply 2A 235mm x 170mm x 87mm

Please note This product is now obsolete but we do have limited quantities available. Please contact us for further information.Vimpex VPSU-24-02A Boxed 24Vdc Power Supply 2A 235mm x 170mm x 87mmThe Vimpex VPSU 12 and VPSU 24 series of PSUs are switched mode power supplies ideal for general use door holders and CCTV cameras.Key FeaturesA 2.0 A 3.0 A 5.0 A versions 5.0 A available as a 12 Vdc model12 Vdc or 24 Vdc versionsUp to 7.0 Ah battery capacities on most modelsHighly efficient power conversion - better than 85Constant current battery charging available on most modelsTamper switch outputSelf-resetting electronic fuse

GBP 57.56

1

Vimpex DC-SAA-102-STD Door Coordinator - Standard Rebate - 102 mm Arm - Anodised Aluminium

Vimpex DC-SAA-102-STD Door Coordinator - Standard Rebate - 102 mm Arm - Anodised AluminiumEnsures that a pair of self-closing fire doors with rebated meeting stiles or security astragals will always shut in the correct sequence regardless of which door is opened first.This clever device operates so that a pair of doors do not incorrectly overlap once the pair of doors are shut. This is particularly important for fire-rated doors and self-latching security doors as it maintains the doors seal.Key FeaturesWeight of door Up to 120 kgsDoor closer size 3-5Width of each leaf Min. 700 mm - Max. 1000 mDoor thickness Min. 38 mm - Max. 58 mmRebate Max.25mm Extended Rebate availableFinishes Silver Anodised Aluminium

GBP 83.66

1

Vesda VSP-005 VLP VLS VLC amp VLF Filter

Vesda VSP-005 VLP VLS VLC VLF FilterThe VESDA replacement filter cartridge is used to replace filter cartridges in VESDA LaserCOMPACT LaserFOCUS LaserPLUS and LaserSCANNER detectors. One model fits all detectors.Importance of Changing the FilterThe filters used in VESDA detectors are key to the performance of the detector. VESDA filers remove dust contamination from the sampled air providing a clean air bleed to preserve the optics in the detection chamber. Like any other filter filters in VESDA detectors must be replaced regularly to ensure optimum efficiency.It is recommended that the filter is replaced in the VESDA VLC VLS VLP and VLF every two years to maintain the operational integrity of the detector you may want to consider replacing the filter more frequently if the detector is used in dusty or dirty conditions. Instructions on how to do this can be found in the replacement instructions in the download section below.Replacing the FilterBefore replacing the filter in your detector it may be necessary to advise any monitoring authorities that the detector may be offline for a short period.Ensure that the area surrounding the filter is clear of dirt and debris and remove the filter. Do not attempt to clean and reuse the filter VESDA filters are intended for single-use only. Once the new filter has been inserted the detector needs to be informed that a new filter has been installed.Key FeaturesEasy swap replacement filterFits VLC VLF VLP and VLS VESDA detectorsAvailable singly or in packs of 2090 mm x 63 mm x 30 mm 3.5 in. x 2.5 in. x 1.2 in.

GBP 69.64

1

Cooper Bi-Wire Option Board 8 Relay BWOB8Z

Cooper Bi-Wire Option Board 8 Relay BWOB8ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 44.39

1

Cranford Controls VPR-MT32-230-W White Sounder 110 230v 32 Tone

Cranford Controls VPR-MT32-230-W White Sounder 110 230v 32 ToneEach device is synchronised via its high frequency oscillator circuit and gives sound outputs with frequencies of between 440Hz - 2850Hz dependant on tone selected. Tones are selected via the DIL switch fitted to the PCB. By using three wires a second stage alarm may be switched so that the continuous tone will override the tone selected.The sounder case material is ABS and is supplied as standard in red. A white version is also available. Each sounder is supplied complete with its own mounting base which contains marker points for drilling two M20 gland entries. The installation of the VPR-MT32-230 sounder is not recommended in industrial areas. These units do not require an earth connection as each device has its own transformer and de-coupling between mains frequencies.

GBP 52.26

1

C-Tec FF502P Four Zone Monitored Sounder Extended Double Gang

C-Tec FF502P Four Zone Monitored Sounder Extended Double GangThe FF502P provides four extra sounder circuits with open and short circuit fault monitoring. It is compatible with most fire alarm control panels and is supplied mounted on a double gang plate which fits standard UK 25mm deep back boxes.Key FeaturesBasic connection requires four wires 24 VDC 0V Sounder Ve Sounder VeSounder -Ve Sounder Ve can be connected at the host panel or any convenient point on a sounder circuit DO NOT SPUR. 24 VDC and 0V can be derived from the host panel or alternatively from an external PSUIf connecting the FF502P to a C-TEC fire panel only three input control wires are required Sounder -Ve is not required as our conventional panels have a common 0V railFits on standard UK 25mm flush or surface mount back boxes

GBP 72.70

1

CommandAlert Weatherproof Site Alarm AE25

CommandAlert Weatherproof Site AlarmAE25Also available in a Wireless Version AE25WSite or temporary fire alarms are commonplace items these days. They offer a customisable and expandable fire alarm system that can easily be moved and altered as a site takes shape.But why are the reliable ones expensive cumbersome and not very loud and the ones that seem loud are just not reliable enoughEnter the CommandAlert Alarm by Commander Is this the ultimate site fire alarm systemAfter years of research and refinement we have developed this brilliant alarm system specifically to fulfil the needs of modern building sites and other applications where a temporary or easily-movable fire alarm system is required.LoudWhen the alarm needs to be raised not only do people have to hear it it has to get through ear protection past the noise of hammers and drills and often over a significant distance. This unit packs an incredible 115dB alarm that ensures no matter where you are the alarm can be clearly heardBrightAs well as being unbelievably noisy this alarm has another way of alerting people a super-bright LED strobe. It produces a brilliant vibrant red flash every 2 seconds and can clearly be seen even in broad daylight.Radio LinkableNeed all the alarms to sound if one is operated No problem. The radio-linkable site alarm links unlimited units together and all units will sound when one is operated. And no complicated programming is required just switch them on The latest radio meshing technology means no control panel is required - the units talk to each other meaning massive versatility and potential range.ToughDesigned from the very outset to be used outside in all winds and weathers this unit is robust and completely waterproof. The ABS plastic is incredibly resistant to breaking even in very cold weather.SimpleThe last thing any installer needs is a fiddly and complex unit to fit. Time is money. So youll find this a refreshing change from the norm The hinged door means you dont have any wiring to do on site simply open the door pop the screws in and youre all set

GBP 45.36

1

Apollo White Multi-Tone Open-Area Sounder - 55000-279APO

Apollo White Multi-Tone Open-Area Sounder - 55000-279APOThe Multi-Tone Open-Area Sounder is designed for use in open areas and can be connected to any Discovery or XP95 system. The Multi-tone Open-Area Alarm Devices are powered directly from the loop and need no external power supply. They operate at 18 28V DC and are polarity sensitive.Synchronisation of the tones ensures the integrity of the signal tones from different sounders do not merge into one signal that could be mistaken for a different tone. A nominal sound output of 100dBA is achieved at a current consumption of 5mA in the case of the sounder and 9mA for the sounder beacon.Many control panels will be able to drive up to 20 sounders per loop on average. The maximum number of sounders that may be connected to a particular loop should however be determined by a loop loading calculation using the Apollo Loop Calculator.Key FeaturesUpdated to include choice of tones Apollo slow whoop and DINTwo volume settings 92dBA and 100dBASynchronisation of tonesIndividual and group addressingLoop PoweredRed or White optionsIP21C rated

GBP 73.40

1

Commander CS23A Compact Double Trolley

Please Note the fire extinguishers and Howler SA01 Alarm in the picture above do not come with the trolley and is for illustrative purposes only.Commander CS23A Compact Double TrolleyA tough powder coated steel frame and nylon wheels guarantee longevity of service even in harsh conditions. It holds 2 extinguishers and can be adapted to take CO2 extinguishers. The small backboard is pre-drilled for fitting a Rotary Alarm Bell and can also be used to fit battery operated fire alarms and other ancillary equipment.The compact design saves space everywhere - in your van in the site store you can fit more on a pallet thereby reducing carriage cost per item. The extinguishers sit low reducing the centre of gravity and making it easy to handle. Supplied empty without the extinguishers and ancillaries shown.Key FeaturesSpace for up to 2 extinguishersNylon wheelsRobust powder coated steel frameCompact space-saving designBackboard allows fitting of Rotary Alarm Bell Howler Site Alarms and other ancillary equipment1200mm h x 470mm w x 400mm d14kg WeightPlease note Due to the size of this product additional delivery charges may occur. Please contact us for further information.

GBP 53.05

1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57

1

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced microphones with standard 3 pin XLR connectors.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.30

1

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.64

1

Brand

Merchant

Price (EUR)