11 results (0,13606 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Nursecall Intercall 101 One Isolator

Nursecall Intercall 101 One Isolator

Nursecall Intercall 101 One IsolatorOne Isolator protects the output from the Controller providing four current limited outputs to distribute the wiring for the nurse call system.SimplicityWith system topology based on decades of experience and reliability the 2 wire Intercall Bus network can often use existing cabling infrastructure for a system upgradeStatusSystem healthy status reassurance LEDProtectionFuse protected outputs for fault isolation

GBP 64.72
1

STI STI-13110FR Univ Stopper - Red Shell - Clear Surface - Fire Label

STI STI-13110FR Univ Stopper - Red Shell - Clear Surface - Fire Label

STI STI-13110FR Univ Stopper - Red Shell - Clear Surface - Fire LabelProtective UV-stabilisedpolycarbonate coverSurfacemount open backedLabel text IN CASE OF FIRE LIFT COVER ACTIVATE FIRE ALARMSuitable for indoor and outdoor applications designed to meet the requirements of IP54ULcUL Listed3 year guarantee against breakage in normal useOther models available colour labelling mountingPlease note Due to the curvature of this model the depth stated will varyVertical installation recommended138 mm H x 116 mm W x 101 mm D

GBP 59.60
1

Cooper Fulleon 640451FULL-0208X Flashni SounderBeacon - Red Lens - White Body - Deep Base

Cooper Fulleon 640451FULL-0208X Flashni SounderBeacon - Red Lens - White Body - Deep Base

Cooper Fulleon 640451FULL-0208X Tone Select Switch Flashni SounderBeacon - Red Lens - White Body - Deep Base Separate Conns for Sounder and BeaconTheFlashni Sounder Beacon Red Lens White Body Deep Base Tone Select Switch Separate Conns for Sounder and Beacon combines audible and visual warning into the one unit.It can output two out of 28 different tones by using a switching voltage to the appropriate terminals.The installer can run either 2 wires for a single tone output or run a 3rd wire to switch the 2nd tone. The sounder is designed to have an output of 101 dBA at 1 metre with a current consumption of only 68 mA.The strobe will flash at a rate of approximately 60 times per minute. Dimension mm 93 x 121 D deep baseKey FeaturesHigh output sounder beaconAutomatic sounder synchronisationVolume controlChoice of lens sounder colour combinationsBase compatible with the Roshni and Solex beaconsLockable base

GBP 44.30
1

Cooper Fulleon 640454FULL-0296X Flashni SounderBeacon - Amber Lens - Red body - Deep base Tone switch

Cooper Fulleon 640454FULL-0296X Flashni SounderBeacon - Amber Lens - Red body - Deep base Tone switch

Cooper Fulleon 640454FULL-0296X Flashni SounderBeacon - Amber Lens - Red body - Deep base Tone switch Separate Conns for Sounder and BeaconTheFlashni Sounder Beacon Red Lens White Body Deep Base Tone Select Switch Separate Conns for Sounder and Beacon combines audible and visual warning into the one unit.It can output two out of 28 different tones by using a switching voltage to the appropriate terminals.The installer can run either 2 wires for a single tone output or run a 3rd wire to switch the 2nd tone. The sounder is designed to have an output of 101 dBA at 1 metre with a current consumption of only 68 mA.The strobe will flash at a rate of approximately 60 times per minute. Dimension mm 93 x 121 D deep baseKey FeaturesHigh output sounder beaconAutomatic sounder synchronisationVolume controlChoice of lens sounder colour combinationsBase compatible with the Roshni and Solex beaconsLockable base

GBP 44.30
1

STI STI-13110CB Universal Stopper Blue Surface Mount Custom Label

STI STI-13110CB Universal Stopper Blue Surface Mount Custom Label

STI STI-13110CB Universal Stopper Blue Surface Mount Custom LabelThese indoor and outdoor low profile or dome polycarbonate covers protect devices such as manual call points emergency buttons and dual action pull stations etc. without restricting legitimate operation. The versatile cover offers excellent protection against physical damage both accidental and intentional dust and grime as well as severe environments inside and out.IMPORTANT NOTICEWhen used on fire systems Universal Stopper is intended for areas where the incidence of false fire alarms from manual call points is high or has proven to be a serious problem. Any disadvantage of the device is more than balanced when one considers the consequences of false fire alarms especially if fire service personnel and equipment are responding to a false fire alarm when they are needed for a real fire somewhere else. Add to this the disruption to the facility when false alarms occur. If you have or may have a problem with false fire alarms or physicalweather damage to your fire alarm activation devices the Universal Stopper could prove invaluable.Details Protective UV-stabilised polycarbonate cover Surface mount open backed Non-Sounder Suitable for indoor and outdoor applications ULcUL Listed Please note Due to the curvature of this model the depth stated will vary 138 mm H x 116 mm W x 101 mm D

GBP 67.55
1

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1

Apollo SA5501-300APO Open-Area Sounder White Body

Apollo SA5501-300APO Open-Area Sounder White Body

Apollo SA5501-300APO Open-Area Sounder White BodyThe Intelligent Open-Area Sounder is designed for use inopen-areas and can be connected to anyCoreProtocol Discovery or XP95 system. The Intelligent Open-Area Sounder includes features such as groupand individual control status reporting and selectable tone and volume settings all configuredthrough the fire control panel.The right tone for the installationThe Intelligent Open-Area Sounder offers a choice of 15 evacuationtones including the standard Apollo evacuation tone. A tone is selected during commissioning inorder to suit local regulations or customs.Whichever evacuation tone is selected there is a secondary tonewhich may be used for alerting or warning of a possible evacuation. The right level of soundThe sounder is set during commissioning to one of sevenlevels of sound the highest level being nominally 101 dbA at 1m. At lessthan 60 dbA the lowest level falls outside the scope of the EN54 standard. Ithas been included to provide a very local warning for the use of personnel in particularenvironments such as nurse stations in hospitals.AddressingThe Open-Area Alarm Devices respond to their own individual address which is set via the appropriate XPERTaddress card. Group address and tones on CoreProtocol systems are set using the fire control panel.Location-specific volume settingDetectors and sounder indicators are installed in manydifferent types of environment. When configuring the Intelligent Open-Area Sounder devicesthe adjustment of the volume can be done at the point of installation. The commissioning engineer simply sets the control panel to Set-upand then walks from one device to the next to set the required volume using amagnetic wand. When all devices have been set the engineer simply presses abutton on the control panel which then registers all the individual volumesettings.Key FeaturesAdjustable tone and volume 15 tone pairs seven volume levelsSoftware defined group addressing with up to 16 group addressesAlarm switching by individual device by group address or ofall individual devices on the loopBuilt-in controllable isolatorSet-up and testing of devices at point of installationUnique acoustic self-test

GBP 46.96
1

Apollo SA5500-300APO Open-Area Sounder Red Body

Apollo SA5500-300APO Open-Area Sounder Red Body

Apollo SA5500-300APO Open-Area Sounder Red BodyThe Intelligent Open-Area Sounder is designed for use inopen-areas and can be connected to anyCoreProtocol Discovery or XP95 system. The Intelligent Open-Area Sounder includes features such as groupand individual control status reporting and selectable tone and volume settings all configuredthrough the fire control panel.The right tone for the installationThe Intelligent Open-Area Sounder offers a choice of 15 evacuationtones including the standard Apollo evacuation tone. A tone is selected during commissioning inorder to suit local regulations or customs.Whichever evacuation tone is selected there is a secondary tonewhich may be used for alerting or warning of a possible evacuation. The right level of soundThe sounder is set during commissioning to one of sevenlevels of sound the highest level being nominally 101 dbA at 1m. At lessthan 60 dbA the lowest level falls outside the scope of the EN54 standard. Ithas been included to provide a very local warning for the use of personnel in particularenvironments such as nurse stations in hospitals.AddressingThe Open-Area Alarm Devices respond to their own individual address which is set via the appropriate XPERTaddress card. Group address and tones on CoreProtocol systems are set using the fire control panel.Location-specific volume settingDetectors and sounder indicators are installed in manydifferent types of environment. When configuring the Intelligent Open-Area Sounder devicesthe adjustment of the volume can be done at the point of installation. The commissioning engineer simply sets the control panel to Set-upand then walks from one device to the next to set the required volume using amagnetic wand. When all devices have been set the engineer simply presses abutton on the control panel which then registers all the individual volumesettings.Key FeaturesAdjustable tone and volume 15 tone pairs seven volume levelsSoftware defined group addressing with up to 16 group addressesAlarm switching by individual device by group address or ofall individual devices on the loopBuilt-in controllable isolatorSet-up and testing of devices at point of installationUnique acoustic self-test

GBP 46.96
1