Pro1.pl | See the cheapest prices and offers on !URL

Notifier HOP-332-110 Door E10 10quot HMI

Notifier HOP-332-110 Door E10 10 HMIThe HOP-332-110 from the Notifier range of products is a door E10 10 HMI designed for use with the inspire range of products.

GBP 1132.44

1

Solo 110 Urban Telescopic Pole 1.75 Metres

Solo 110 Urban Telescopic Pole 1.75 MetresThe Solo 110 Access Pole offers safe access to detectors installed at heights of up to 3 metres. Solo poles should always be held vertically when raising or lowering. Ensure that all extension poles and test tool buttons are locked into position before extension and use. The maximum working height using Solo 110 Solo 111 poles is 4.5 metres for Solo and Testifire. This is achieved using 1 x Solo 110 telescopic pole and a maximum of 3 x Solo 111 extension poles. It is recommended to stand directly under the detector.Key FeaturesExtends to 1.75 metres to provide maximum reach of 3 metresCan be used with up to 3 Solo 111 extension polesPull-wound glass fibre constructionDesigned certified non-conductiveSimple locking mechanismCompatible with the Solo 612 Pole BagUrban telescopic and extension poles are half the length of conventional poles

GBP 610.40

1

Morley DXc Region 2 - Morley Only 2 Loop Base Card 795-110-002

Morley DXc Region 2 - Morley Only 2 Loop Base Card 795-110-002DXc region 2 2 loop base card.Region 2 Morley only

GBP 1246.19

1

Morley DXc Region 1 - Apollo Hochiki System Sensor 1 Loop Base Card 795-110-001

Morley DXc Region 1 - Apollo Hochiki System Sensor 1 Loop Base Card 795-110-001DXc region 1 2 loop base card.Region 1Apollo Hochiki System Sensor

GBP 1291.63

1

Fireclass 516.016.236FC ProReact 110 Degree C IndoorOutdoor Cable Tie UV amp Heat Stabilised - Pack of 100

Fireclass 516.016.236FC ProReact 110 Degree C IndoorOutdoor Cable Tie UV Heat Stabilised - Pack of 100The 516.016.236FC is a pack of ProReact 110 Degree C IndoorOutdoor Cable Ties.Installation standards such as BS5839 part 1 specify non-combustible cable supports and this requirement extends to linear heat sensor cable. To satisfy this requirement the ProReact Analogue Heat Detector range includes a range of fixings in either Zintec or Stainless Steel and compatible cable ties.Key FeaturesPack of 100Suitable for indoor and outdoor useUV and heat stabilised

GBP 1594.80

1

International Gas Detectors TOC-750-50 TOCSIN 750 Control Panel - Single Highway 110-230VAC

International Gas Detectors TOC-750-50 TOCSIN 750 Control Panel - Single Highway 110-230VACKey FeaturesThe latest addressable technology from International Gas Detectors.Communication over PowerOnly uses 2 Core Cable for Power and Communication.Polarity Independent.Typical System is 40 Faster to Install with Fewer ConnectionsImproved reliabilityImproved connectivity to external systemsRe-use Existing Cabling When Updating ATEX and Safe Area Gas DetectorsUSB For Backup and Data CollectionEthernet ConnectivityFull Event Monitoring Time Date Stamped Rs485 BMS Connectivity

GBP 1630.80

1

Solo 423 - Mains Heat Detector Test Kit - 110 120 Volt

Solo 423 Mains Heat Detector Test Kit - 110 120 VoltThe Solo 423 is a professional and robust tool for testing heat detectors fitted at heights of up to 9 metres. Unlike the Solo 461 it does require a power cord mains lead but conversely does not require any special energy saving features.Designed for use on fixed temperature rate of rise and combination detectorsSuitable for any type of make of spot point type heat detectorLarge clear cup fits over detector enabling a clear view of the detector LEDTests detectors up to 90 degrees C 194 degrees F operating temperatureThermal cut-out for added protectionSupplied with 5m cable as standard Can be extended to 10m using Solo 425 5m extension

GBP 766.20

1

Morley TL-2055 Flame FS20X24X Test Lamp Hazardous Area

Morley TL-2055 Flame FS20X24X Test Lamp Hazardous AreaTL-2055is a Class I Div. 1 approved Explosion-Proof Test Lamp designed for testing the FS24X Detectors externally in a hazardous location. The hand held Test Lamp see Figure 4-2 comes with a Universal Charger 110 VAC and 220 VAC.

GBP 5455.68

1

Kidde 2X-AT-F2 Addressable Fire Panel Touch Screen With UI - 2 Loop

Kidde 2X-AT-F2 Addressable Fire Panel Touch Screen With UI - 2 LoopAn addressable fire panel with 7 touch screen and UI. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colourDimensions 446 x 536 x 164 mm

GBP 1133.33

1

Kidde 2X-AT-F2-FB-P Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Big PSU

Kidde 2X-AT-F2-FB-P Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Big PSUAn addressable fire panel with 7 touch screen UI and FB Control. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1513.93

1

Kidde 2X-AT-F2-FB-S Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small CAB

Kidde 2X-AT-F2-FB-S Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small CABAn addressable fire panel with 7 touch screen UI and FB Control. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1209.06

1

Kidde 2X-AT-F2-FB Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small Cab

Kidde 2X-AT-F2-FB Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small CabAn addressable fire panel with 7 touch screen UI and FB Control. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colourDimensions 446 x 536 x 164 mm

GBP 1209.06

1

Solo 613 Urban Lightweight Backpack amp Poles Kit

Solo 613 Urban Lightweight Backpack Poles KitA lightweight practical kit that provides the perfect balance of carrying test equipment for testing up to 4.5 meters alongside your other on-site essentials. A flexible backpack ideal for use on large sites or city working. Includes space for your essential test kit devices small tools accessories. Designed for allowing engineers to move easily around towns large sites or buildings without the need to carry bulk poles and bags.The kit includes a pole bag which comes complete with 1 x 110 1.75m telescopic 3 x 111 0.5m extension poles. The poles are designed to work in conjunction with each other and are used to test detectors up to a maximum working height of 4.5 metres. The pole bag is fastened onto the backpack using adjustable clips.Key FeaturesCustomisable main interior for test equipment battery batons accessoriesPadded compartment for Laptop or tabletLarge zipped pockets for cartridges smaller essentialsFront pocket for A4 notepad small tool sets etc.Clear pocket to promote your own brand or businessAdjustable quick-release clips for Solo 612 Pole bagWide shoulder straps and padded backChest strap for weight balanceLightweight design allows fast and efficient testingPoles are design from a pull-wound glass fibre constructionSimple locking mechanism on the polesUrban telescopic and extension poles are half the length of conventional polesCabin luggage compatible - Based on backpack dimensions. Please check with your individual airline as baggage allowances vary. Poles length 620mm may be allowed when held diagonallyKit Contains1 x Solo 611 Urban Lightweight Backpack1 x Solo 612 Urban Pole Bag1 x Solo 110 Urban 4-section Telescopic Pole 1.75m3 x Solo 111 Urban Extension Poles 0.5m

GBP 1398.04

1

Zeta S64CO Simplicity CO Carbon Monoxide Panel - 4 Zone - 64 Devices - Plastic Enclosure

Zeta S64CO Simplicity CO Carbon Monoxide Panel - 4 Zone - 64 Devices - Plastic EnclosureThe Simplicity CO system is a self-conditioned controller with a capacity to handle up to 110 CO monitors which are divided to 8 monitoring zones.Each Zone will permanently display on the Liquid Crystal Display LCD the highest concentration of CO in that zone in PPM Particles Per Million. This monitored value is updated every 10 seconds. The system will allow up to 2 interface modules ZIOUI-230 which are programmed to initiate a signal to Ventilation equipments to operate at pre-determined levels of concentration. Should the CO concentration keep rising while the Ventilation is still on an alarm is raised at a pre-determined level.Key FeaturesAddressable carbon monoxide system2-4 zones with a maximum of 64 devicesRadial or Loop wiring formats selectable on panelSuitable for many applications including underground carparks

GBP 539.51

1

Zeta S126CO Simplicity CO Carbon Monoxide Panel - 8 Zone - 126 Devices - Plastic Enclosure

Zeta S126CO Simplicity CO Carbon Monoxide Panel - 8 Zone - 126 Devices - Plastic EnclosureThe Simplicity CO system is a self-conditioned controller with a capacity to handle up to 110 CO monitors which are divided to 8 monitoring zones.Each Zone will permanently display on the Liquid Crystal Display LCD the highest concentration of CO in that zone in PPM Particles Per Million. This monitored value is updated every 10 seconds. The system will allow up to 2 interface modules ZIOUI-230 which are programmed to initiate a signal to Ventilation equipments to operate at pre-determined levels of concentration. Should the CO concentration keep rising while the Ventilation is still on an alarm is raised at a pre-determined level.Key FeaturesAddressable carbon monoxide system2-8 zones with a maximum of 126 devicesRadial or Loop wiring formats selectable on panelSuitable for many applications including underground carparks

GBP 584.18

1

Ziton 2010-2F2-MB ZP2 Main PCB - 2 Loop

Ziton 2010-2F2-MB ZP2 Main PCB - 2 LoopThe 2010-2F2-MB is a replacement main board for all ZP2 2 loop control panels.Key Features2 ring with up to 128 zones and main detector control unitAuto-configuration and regional commissioning modeEthernet port with TCP IP for remote maintenance and programmingAll Terminals pluggable3 USB ports with memory stick support3 RS232 interfaces24 V DC supply alarm switch with reset functionVdS approval G 210005Technical SpecificationsPower supply Operating voltage 230110 V AC 10 -15Operating Current Nom. 0.6 1.3 A Max. 1.5 3.15 AFrequency 5060 Hz 5Backup 24 ACable Type 3 x 1.5 mm line neutral earthOutputs Fire Alarm fault monitors 2350 mA 19.5 to 28 V DCProgrammable monitored 2750 mA 19.5 to 28 V DCAUX 1 switched 500 mA 19.5 to 28 V DCFire Alarm fault relay 2Terminator AG 15 kOhmInputs Programmable 2Maximum load 150mATerminator EC 15 kOhmCable Characteristics Outputs 1250 mA 29 V DC to 36 V DCCable length 56ohm 1uF max. 4 kmEnvironmental conditions Storage temperature -20 C to 50 COperating temperature -5 C to 40 CDimensions Overall dimensions W x H 320 x 110 mmAdmission VdS Approved G 211005

GBP 514.81

1

Zeta S126COM Simplicity CO 126 Addressable CO Panel - 8 Zone 126 Device in Metal Enclosure

Zeta S126COM Simplicity CO 126 Addressable CO Panel - 8 Zone 126 Device in Metal EnclosureThe Simplicity CO system is a self-conditioned controller with a capacity to handle up to 110 CO monitors divided over 8 monitoring zones. Each zone is permanently shown on the LCD display along with highest concentration of CO within that zone measured in PPM Particles Per Million. This monitored value is updated every 10 seconds.Each system allows up to 2 interface modules ZIOUI-230 which are programmed to initiate a signal to ventilation equipment. These will trigger at predetermined levels of CO concentration and should this concentration keep rising while the ventilation is still on an alarm is raised at a further pre-determined level.The Simplicity CO system is ideal forUnderground car parking facilitiesWarehouses where non-electric fork lift vehicles are usedTunnelsFactoriesBoiler Rooms etcKey FeaturesAlarm Output 2 x 150mA 24 VdcPanel Size mm 370W x 311H x 113DSpace for Batteries Up to 2 x 7.0 AH SLA BatteriesWeight 4KgHow is CO GeneratedCarbon Monoxide is a by-product of combustion. Any fuel burning appliance vehicle tool or other device has the potential to produce dangerous levels of Carbon Monoxide.The Simplicity CO 8 system is designed to detect monitor CO concentrations in places such as warehouses car parks tunnels and enclosed buildings where forklifts cars and delivery trucks can produce deadly amounts of carbon monoxide in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.What is the Simplicity COThe Simplicity CO system was designed to be simple to use addressable carbon monoxide detection and ventilation system capable of detecting low concentrations of CO and automatically starting the buildings ventilation fans. Its features includeTrue analogue addressable systemEconomical 2 wire installationCan view the PPM reading of every detectorEach detector can be given a 20-character label to ease device identification optional.Loop of 126 devices divided into 8 zonesContinuously displays the maximum reading in each zoneOption for 2 ventilation relays per zone for systems with 2 speed fansZonal or common ventilation optionsEasy to use ventilation level selection Battery backup enables the system to give an alarm warning in the case of mains power failureSystem programming is determined by detector relay address settingsSuitable for small and large installationsDesigned Manufactured in the UKMeets latest low voltage directive CE marked

GBP 762.88

1

Zeta S32CO Simplicity CO 32 Addressable CO Panel - 2 Zone 32 Devices

Zeta S32CO Simplicity CO 32 Addressable CO Panel - 2 Zone 32 DevicesThe Simplicity CO system is a self-conditioned controller with a capacity to handle up to 110 CO monitors which are divided to 8 monitoring zones.Each Zone will permanently display on the Liquid Crystal Display LCD the highest concentration of CO in that zone in PPM Particles Per Million. This monitored value is updated every 10 seconds. The system will allow up to 2 interface modules ZIOUI-230 which are programmed to initiate a signal to Ventilation equipment to operate at pre-determined levels of concentration. Should the CO concentration keep rising while the Ventilation is still on an alarm is raised at a pre-determined level.The Simplicity CO system is ideal forUnderground car parking facilitiesWarehouses where non-electric fork lift vehicles are usedTunnelsFactoriesBoiler Rooms etcKey FeaturesAlarm Output 2 x 150mA 24 VdcPanel Size mm 370W x 311H x 113DSpace for Batteries Up to 2 x 7.0 AH SLA BatteriesWeight 4KgHow is CO GeneratedCarbon Monoxide is a by-product of combustion. Any fuel burning appliance vehicle tool or other device has the potential to produce dangerous levels of Carbon Monoxide.The Simplicity CO 8 system is designed to detect monitor CO concentrations in places such as warehouses car parks tunnels and enclosed buildings where forklifts cars and delivery trucks can produce deadly amounts of carbon monoxide in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.What is the Simplicity COThe Simplicity CO system was designed to be simple to use addressable carbon monoxide detection and ventilation system capable of detecting low concentrations of CO and automatically starting the buildings ventilation fans. Its features includeTrue analogue addressable systemEconomical 2 wire installationCan view the PPM reading of every detectorEach detector can be given a 20-character label to ease device identification optional.Loop of 126 devices divided into 8 zonesContinuously displays the maximum reading in each zoneOption for 2 ventilation relays per zone for systems with 2 speed fansZonal or common ventilation optionsEasy to use ventilation level selection Battery backup enables the system to give an alarm warning in the case of mains power failureSystem programming is determined by detector relay address settingsSuitable for small and large installationsDesigned Manufactured in the UKMeets latest low voltage directive CE marked

GBP 515.45

1

Zeta S64COM Simplicity CO 64 Addressable CO Panel - 4 Zone 64 Device in Metal Enclosure

Zeta S64COM Simplicity CO 64 Addressable CO Panel - 4 Zone 64 Device in Metal EnclosureThe Simplicity CO system is a self-conditioned controller with a capacity to handle up to 110 CO monitors which are divided to 8 monitoring zones.Each Zone will permanently display on the Liquid Crystal Display LCD the highest concentration of CO in that zone in PPM Particles Per Million. This monitored value is updated every 10 seconds. The system will allow up to 2 interface modules ZIOUI-230 which are programmed to initiate a signal to Ventilation equipment to operate at pre-determined levels of concentration. Should the CO concentration keep rising while the Ventilation is still on an alarm is raised at a pre-determined level.The Simplicity CO system is ideal forUnderground car parking facilitiesWarehouses where non-electric fork lift vehicles are usedTunnelsFactoriesBoiler Rooms etcKey FeaturesAlarm Output 2 x 150mA 24 VdcPanel Size mm 370W x 311H x 113DSpace for Batteries Up to 2 x 7.0 AH SLA BatteriesHow is CO GeneratedCarbon Monoxide is a by-product of combustion. Any fuel burning appliance vehicle tool or other device has the potential to produce dangerous levels of Carbon Monoxide.The Simplicity CO 8 system is designed to detect monitor CO concentrations in places such as warehouses car parks tunnels and enclosed buildings where forklifts cars and delivery trucks can produce deadly amounts of carbon monoxide in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.What is the Simplicity COThe Simplicity CO system was designed to be simple to use addressable carbon monoxide detection and ventilation system capable of detecting low concentrations of CO and automatically starting the buildings ventilation fans. Its features includeTrue analogue addressable systemEconomical 2 wire installationCan view the PPM reading of every detectorEach detector can be given a 20-character label to ease device identification optional.Loop of 126 devices divided into 8 zonesContinuously displays the maximum reading in each zoneOption for 2 ventilation relays per zone for systems with 2 speed fansZonal or common ventilation optionsEasy to use ventilation level selection Battery backup enables the system to give an alarm warning in the case of mains power failureSystem programming is determined by detector relay address settingsSuitable for small and large installationsDesigned Manufactured in the UKMeets latest low voltage directive CE marked

GBP 681.78

1

Cooper Menvier EFDAU500 Compact Wall Mounted Voice Alarm System

Cooper Menvier EFDAU500 Compact Wall Mounted Voice Alarm SystemThe networked voice alarm and public address system Compact DAU500 is based on the concept of a standalone or decentralised network topology with multi-channel amplifier and built-in local power backup. This state-of-the-art digital technology offers an audio distribution system which is a compact all-in-one wall-mounted solution where a flexible and easy to operate voice system installation.Compact DAU500 can be configured as a standalone or networked voice alarm system comprising of 6 loudspeaker circuits and consists of a central control unit with embedded amplifier cards 3 dual-channel amplifier cards EF-DA200 for 6 zones plus one dual-channel amplifier EF-DA200 for active back-up with integrated emergency power manager in accordance with EN54-4.Compact DAU500 is an optimised voice alarm andor public address system designed for small and medium sized applications. A standalone central control unit together with three EF-DA200 two channel amplifiers forms a complete voice alarm system for venues such as schools smaller hotels etc. The overall system achieves the performance requirements for voice alarm systems in accordance with EN54-16 and electro-acoustic emergency warning systems EN 50849.The Compact DAU500 central control unit has a built-in EN54-4 certified power supply equipment complete with 4 ampere intelligent charger and battery compartment.Each DAU500 panel supports memory storage for 22 pre-recorded messages of max. 5 minutes each they can be configured for alarm messages and signals evacuation alarm warning siren and attention signals siren chime. The volume of each source and each amplifier channel can be regulated using the 5-point parametric audio filter which is available for each input and output. Faults are recognized displayed and logged in compliance with standards within a few seconds.The Compact DAU500 central unit features 2 analogue balanced inputs for background music or an external analogue priority signal that can trigger an evacuation status.As standard the DAU500 panel is equipped with 6 independent amplifier channels which can operate a total of 6 loudspeaker circuits each loaded with a maximum of 100W. Amplifier channels can be bridged in pairs creating more powerful loudspeaker lines each capable of driving a 200W loudspeaker load. It is also possible to mix branch and loop line technology on the same central control unit. The number of loudspeaker circuits can be further expanded using the EF-HEXAPOD6 multiplexer units for phased evacuation applications the maximum number of loudspeaker circuits possible from a single DAU500 panel is 18 lines this limit can be extended further to 36 loudspeaker lines in non-phased evacuation applications.The Compact DAU500 directs two live stream audio channels and a serial data channel RS422 into remote zones via a redundant global network loop and controls a 6-channel message player that sends synchronized audio signals to the local zones. In this way each Compact DAU500 can play multiple audio messages simultaneously in the local zones. All announcement memory modules are synchronized between several Compact DAU500 panels supporting a wide area of warning message playback.Key FeaturesCompatible charger for 24 V DC backup batteries according to national standardsBattery backup storage for 24V battery from 10Ah to 55Ah2 x global network ports RJ45 for redundant ring monitored3 x local network ports RJ45 for local IO devices monitored2 x BGM one reserved for the fire station in the front panel8 x GPI terminal block opto-isolated8 x GPO terminal block open collectorSecured potential-free relay output EVAC FAULT RESETSecure input RESET SILENCE 6 x EVACLocal message player with storage of 22 audio files total length 110 minutesUSB interfacePre-programmed and exchangeable microSD cardControl and display board national language optionalFire station with access protection level 220kHz AC end-of-line monitoring with impedance deviation measurement EOLLoop line technology with LoopDrive 54-17 certified6x 100W or 3x 200W bridged continuous powerClass D 100V outputsOutput power at 230V mains voltage 6 x 100WOutput power with 24V DC emergency power supply 6 x 100WFrequency response 50Hz to 20KHz 3dBDistortion factor 0.1 at 1 kHz sineSignal to noise ratio 90dB A - weightedChannel separation 80dBEfficiency at maximum performance 80

GBP 8409.46

1

Brand

Merchant

Price (EUR)