5 results (0,14260 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Ziton Z-AUXD-2P Deep Base Mounting Polar White

Ziton Z-AUXD-2P Deep Base Mounting Polar White

Ziton Z-AUXD-2P Deep Base Mounting Polar WhiteThe Z-AUXD-2P is a surface mounting base accessory that allows detectors to be installed using standard 20 or 25 mm electrical conduit. Four flat surfaces are provided on the wall of the moulding to accommodate side entry glands together with a breakout in the base of the unit for rear entry cables.The Z-AUXD-2P is compatible with all ZP7 and Z6 series detector bases. It features fixing slots for either direct ceiling mounting or alternate connection to most standard conduit boxes.Key FeaturesAccepts conduit sizes up to 25 mmCompatible with all ZP7 and Z6 series detector basesSide and rear wiring entry

GBP 3.78
1

Patol 700-660 quotPquot Clip with Neoprene Insulator - Internal Diameter 3mm

Patol 700-660 quotPquot Clip with Neoprene Insulator - Internal Diameter 3mm

Patol 700-660 P Clip with Neoprene Insulator - Internal Diameter 3mmStainless-steel P clip with rubber protection. Ideal for use with LHDC Product Codes700-001 - Patol 700-701 Digital Zener Barrier - MTL - For Use With LDM-519-DIM Only700-005 - Patol 700-705 Digital Galvanic Barrier MTL700-070 - Patol Digital 70C Black Nylon Sheath Price per Meter700-090 - Patol Digital 90C Black Nylon Sheath Price per Meter700-180 - Patol Digital 180C Violet Hytrel Sheath Price per Meter

GBP 0.72
1

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APOAll detectors in the Soteria XP95 and Discovery range fit into the XPERT 8 Intelligent Mounting Base.The base has a wide interior diameter for ease of access to cables and terminals. The E-Z Fit feature allows you to fit the base screws place the XPERT 8 Intelligent Mounting Base over the screws slide it into place and tighten the screws.The detector requires a clockwise rotation into the base for fitting. Additionally the detector can be locked into the base for increased security by a grub-screw using a 1.5mm hexagonal driver.The XPERT 8 card part number 38532-064 supplied with the base has pre-punched pips to remove to set the address. Refer to the Coding Guide for details on how to set the address.Backwards CompatibilitySoteria detectors have been designed to operate on XP95 and Discovery loops. This allows for Soteria detectors and bases to operate on existing systems and for Soteria detectors to operate on XP95 and Discovery bases XPERT 7 Intelligent Mounting Base. It should be noted that not all features of Soteria will be available when used with XP95 or Discovery fire control panels. If Soteria detectors are used with XP95 fire control panels incorporating drift compensation algorithms these must be disabled when communicating with Soteria devices.When Soteria detectors are used with an XPERT 7 Intelligent Mounting Base on a CoreProtocol system Soteria devices will have a 128 address offset due to only 7 address pips being available on the XPERT 7 card. For example an XPERT 7 card set at 32 will address as 160 on CoreProtocol with Soteria detectors.Key FeaturesCompatibility with Soteria XP95 and Discovery detectorsIsolated and Non-isolated devices supportedIsolated wiper - maintains loop connectivity during temporary removal of devicesXPERT 8 card for Core-ProtocolE-Z Fit allows for simple mounting of the detector base after wiringKeyed to accept only addressable devicesBase mark allows for LED detector alignmentPlease Note XPERT 8 card increase the address capacity to 254 when using Soteria detector and Core-Protocol enabled fire control panel.

GBP 2.64
1