Pro1.pl | See the cheapest prices and offers on !URL

Kidde Airsense APIC Card Notifier Protocol 9-30433

Kidde Airsense APIC Card Notifier Protocol 9-30433APIC cards plug into a connector on the main PCB provided for that purpose. To use the Notifier APIC all that is required is to plug the card into this connector using the ribbon cable attached to the interface connect loop in and loop out on the terminals on the detector PCB and set the switches to the loop address. The APIC has two distinct modes of operation single address and multi address. When the interface is set to single address mode the card is set to a single address on the Notifier loop and the detector status is read from that address.Multi address mode is used when monitoring the status of multiple detectors with consecutive addresses from a single APIC card. Multi address mode is normally only used in the Command Module. Two pairs of switches Highest and Lowest on the APIC card enable the card to either respond as a single address as it does in a detector or a range of addresses which is the way it is set up in the Command Module.To set up an APIC in a detector which only requires a single address single address mode set both pairs of switches to the required address on the Notifier loop. This sets the card to single address mode. The APIC pictured is set to single address mode at address 15.

GBP 181.16

1

NC-BA-SM-W Conventional Base Accessory - Surface Mount White

NC-BA-SM-W Conventional Base Accessory - Surface Mount WhiteThe NC-BA-SM-W is an NC-Series surface mount base accessory.It allows cabling to be installed by running standard electrical conduitdirectly into the base leaving no exposed cabling.PreparationThe standard rear cable entry into the base is availablewith the same wide opening dimensions to the standard base with ample room forcables. In addition four entry points are provided on the wall of the fixtureto accommodate side entry spaced at 90 around the base to allow entry andexit in all directions.InstallationThe conduit entry points are conveniently supplied withbreakouts. Keyhole screw fixing locations adds to the ease of installation.The standard NC-Series detector base fits snugly on top ofthe fixture completing the installation with the same feature set as forstandard surface mount installation for quick easy and secure detectorplacement.Key FeaturesLarge rear cable entry with ample space for cablesSide conduit entry protects cables from damageBreakout support for conduit entryInstallation fixture with first fix screw option reducesinstallation time and effortAllows surface cabling for all NC-Seriesconventional detector bases

GBP 1.50

1

Kidde NC-D-PT Conventional Device Programmer

Kidde NC-D-PT Conventional Device ProgrammerThe NC-D-PT is a hand-held tool for programming and configuration ofNC-Series conventional point and beam detectors. It can be used toread parameters and set the operating modes and sensitivities ofthese devices if the default settings require adjustment for harcher orspecial applications.Key FeaturesHand held portableEasy operation4-digit alphanumeric LCD displayLow-consumption hibernation and power saving functions extends the operating timeBattery low indication

GBP 152.66

1

Kidde Airsense Stratos-HSSD 2 Standard Detector 9-30621

Airsense Stratos-HSSD 2 Standard Detector9-30621Stratos-HSSD has unmatched sensitivity potential providing the earliest warning of incipient fire with minimum rate of nuisance alarms.ClassiFire perceptive artificial intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the detector will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.Volt-free fire and fault relay outputs are available for remote monitoring by local fire detection or BMS system. Each detector is provided with 3 pairs of remote control input terminals. The inputs may be configured for a number of functions.Key Features High sensitivity provided by laser based forward light scatter for reliable early warningUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D laster dust discrimination and elimination system4 sampling pipes up to 250m maximum total lengthRS485 communications built in as standard for networking and remote communications

GBP 2286.74

1

Kidde Airsense Stratos-HSSD 2 - Minimum Display Version 9-30710

Stratos-HSSD 2 - Minimum Display Version9-30710Stratos-HSSD has unmatched sensitivity potential providing the earliest warning of incipient fire with minimum rate of nuisance alarms.ClassiFire perceptive artificial intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the detector will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.Volt-free fire and fault relay outputs are available for remote monitoring by local fire detection or BMS system. Each detector is provided with 3 pairs of remote control input terminals. The inputs may be configured for a number of functions.Key Features High sensitivity provided by laser based forward light scatter for reliable early warningUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D laster dust discrimination and elimination system4 sampling pipes up to 250m maximum total lengthRS485 communications built in as standard for networking and remote communications

GBP 2068.55

1

Kidde Airsense Command Module Without Stratos-HSSD 2

Command Module Without Stratos-HSSD 2Stratos-HSSD has unmatched sensitivity potential providing the earliest warning of incipient fire with minimum rate of nuisance alarms.ClassiFire perceptive artificial intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the detector will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.Volt-free fire and fault relay outputs are available for remote monitoring by local fire detection or BMS system. Each detector is provided with 3 pairs of remote control input terminals. The inputs may be configures for number of functions.Key Features High sensitivity provided by laser based forward light scatter for reliable early warningUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D laster dust discrimination and elimination system4 sampling pipes up to 250m maximum total lengthRS485 communications built in as standard for networking and remote communications

GBP 1809.85

1

Kidde 1-23911-K085 FireBeta XT 4 Zone 2 Area Extinguishing Panel

Kidde 1-23911-K085 FireBeta XT 4 Zone 2 Area Extinguishing PanelThe Kidde 1-23911-K085 FireBeta XT 4 Zone 2 Area Extinguishing Panel is a multi-area extinguishing control panel complying with EN12094-1 EN54-2 and EN54-4. It offers 4 detection zones for controlling 2 extinguishing areas. Each extinguishing area has a comprehensive set of inputs and outputs and is configurable via a simple programming interface. All extinguishing areas may have up to 7 serially connected status indication and control units connected via a simple 4 core cable. The versatility of the control panel may be further enhanced by the fitting up to 7 ancillary or sounder boards to the RS485 serial bus.Key FeaturesProgrammable extinguishing delays and output durationExtract fan controlA countdown indicator shows the timeMode select and manual release controls per areaMonitored abort inputSerial connection for status units and ancillary boards

GBP 1088.75

1

Kidde Airsense Stratos-HSSD 2 Detector Fitted With Command Module 9-30620

Stratos-HSSD 2 Detector Fitted With Command Module9-30620Stratos-HSSD has unmatched sensitivity potential providing the earliest warning of incipient fire with minimum rate of nuisance alarms.ClassiFire perceptive artificial intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the detector will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.Volt-free fire and fault relay outputs are available for remote monitoring by local fire detection or BMS system. Each detector is provided with 3 pairs of remote control input terminals. The inputs may be configured for a number of functions.Key Features High sensitivity provided by laser based forward light scatter for reliable early warningUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D laster dust discrimination and elimination system4 sampling pipes up to 250m maximum total lengthRS485 communications built in as standard for networking and remote communications

GBP 3376.46

1

Kidde AirSense Stratos HSSD 2 Detector in Steel Enclosure 9-30706

Kidde AirSense Stratos HSSD 2 Detector in Steel Enclosure 9-30706Stratos HSSD2 is designed to provide very high sensitivity smoke detection ensuring the very earliest warning of incipient fire with minimum rate of nuisance alarms. ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup.This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area. Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems. Command module available for central monitoring and display.Typical ApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesHigh sensitivity provided by laser based forward light scatter for reliable early warningCombined sampling pipe up to 200m in length still airUnique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and dust separation system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination systemRS485 communications built in as standard for networking and remote communicationsLarge area aspirating smoke detector up to 2000m2 coverageCPR LPCB VdS NF CSIRO UL FM approved

GBP 2231.89

1

Kidde Airsense APIC Card Hochiki Protocol 9-30438

Kidde Airsense APIC Card Hochiki Protocol 9-30438The 9-30438 is an interface which can be attached directly onto the main control board of any of the AirSense aspirating detectors. The card plugs into the main control board inside the detector enclosure. The board enables the detector to be directly addressed and communicate with the main fire control panel via the Hochiki protocol.The Hochiki APIC has two distinct modes of operation single address and multi address. When the interface is set to single address mode the card appears at a single address on the Hochiki loop and the detector status is read from that address. Multi address mode is used when monitoring the status of multiple detectors with consecutive addresses from a single Hochiki card. Multi address mode is normally only used in the Command Module.Detectors are wired onto the loop using plug in terminals located on the detector main control board. The detector and interface are easily addressed by switch settings prominently positioned on the card.Key FeaturesSimple addressing onto the addressable loopRibbon cable connection no hard wiringPiggy backs onto detector main boardEase of address setting

GBP 163.42

1

Kidde 1-23911-K087 FireBeta XT Extinguishing Control Panel 4 Zone 1 Area

Kidde 1-23911-K087 FireBeta XT Extinguishing Control Panel 4 Zone 1 AreaThe FireBeta XT 4 Zone 1 Area is a single-area extinguishing control panel complying with EN12094-1 EN54-2 and EN54-4. It offers 4 detection zones for controlling 1 extinguishing area.The extinguishing area has a comprehensive set of inputs and outputs and is configurable via a simple programming interface. It may have up to 7 serially connected status indication and control units connected via a simple 4 core cable.The versatility of the control panel may be further enhanced by the fitting up to 7 ancillary or sounder boards to the RS485 serial bus.Key FeaturesEN12094-1 EN54-2 and EN54-4 approvedFour detection zones and 1 extinguishing areas as standardDual configurable extinguishing outputs as well as first and second stage sounder outputsFirst and second stage potential free changeover contactsAgent released and common fault potential free contactProgrammable extinguishing delays and output durationExtract fan controlA countdown indicator shows the time in seconds until releaseMode select and manual release controlsMonitored remote inputs for manual release hold mode select door interlock released pressure switch and low pressure switchMonitored abort inputSerial connection for status units and ancillary boards

GBP 856.69

1

Kidde AirSense Stratos HSSD 2 Detector with Command Module in Steel Enclosure 9-30707

Kidde AirSense Stratos HSSD 2 Detector with Command Module in Steel Enclosure 9-30707Stratos HSSD2 is designed to provide very high sensitivity smoke detection ensuring the very earliest warning of incipient fire with minimum rate of nuisance alarms. ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup.This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area. Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems. Command module available for central monitoring and display.Typical ApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesHigh sensitivity provided by laser based forward light scatter for reliable early warningCombined sampling pipe up to 200m in length still airUnique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and dust separation system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination systemRS485 communications built in as standard for networking and remote communicationsLarge area aspirating smoke detector up to 2000m2 coverageCPR LPCB VdS NF CSIRO UL FM approved

GBP 3320.40

1

Kidde Airsense Micra 10 Single Pipe Aspiration Smoke Detector 9-30725

Kidde Airsense Micra 10 Single Pipe Aspiration Smoke Detector 9-30725The AirSense Micra 10 is designed to provide very high sensitivity smoke detection in a small package. ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.The detector is designed to fit into a Docking Station. All sampling pipes and cables are connected to the Docking Station as a first fix operation leaving the detector to be fitted during the final commissioning phase if required. This ensures that detectors are less likely to be damaged during the installation. Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems.ApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesUltra-small low-cost aspirating smoke detector for easy and discreet installationHigh sensitivity provided by laser based forward light scatter for reliable early warningSingle sampling pipe up to 50m in length still airUnique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and dust separation system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination system

GBP 888.07

1

Kidde 1-23911-K116 FireBeta A-XT Extinguishing Control Panel

Kidde 1-23911-K116 FireBeta A-XT Extinguishing Control PanelThe Kidde 1-23911-K116 FireBeta A-XT Extinguishing Control Panel is a ULFM listed extinguishing control panel designed and manufactured to the highest standards in a quality controlled environment. With UL and FM approvals it offers outstanding value and performance for small to medium sized fixed firefighting installations. FireBeta A-XT is supplied in a red enclosure.The 3 initiation circuits allow extinguishant release to be configured to activate from any combination of detection zone inputs. This allows among others any 2 zones from the combination of 3 to activate release making it ideal for applications protecting ceiling room and floor voids.The extensive configuration options of the FireBeta A-XT allow the functionality of the system to be extensively modified. A large LED display on the panel fascia enables easy configuration and control. It additionally displays the time remaining until extinguishing agent release for added user safety.Key FeaturesUL864 and FM listedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stepsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining to releaseSupports up to seven four wire status indicatorsBuilt in extract fan control

GBP 536.48

1

Kidde KE-DBA-IPW Intelligent Addressable IP Base Accessory White

Kidde KE-DBA-IPW Intelligent Addressable IP Base Accessory WhiteThe innovative Excellence range of intelligent addressabledevices offers advanced features for reliability and peace of mind. Coupledwith features for ease of installation and maintenance on new fire detectionsystems its a perfect match for exceptional overall performance.The KE-DBA-IPW is an Excellence series surface mount baseaccessory. It allows loop cabling to be installed in wet environments byallowing the use of cable glands to seal the cable entry into the base fromwater ingress via the cables. Four entry points are provided on the wall of thebase to accommodate side entry glands. Rear cable entry into the base is alsoavailable with two similar cable gland knockouts.InstallationThe conduit entry points are conveniently supplied withbreakouts and drill locations to facilitate either installation method.The standard Excellence series detector base fits snugly insidethe fixture completing the installation with the same feature set as forstandard surface mount installation including address tag mounting ability intwo locations head locking to avoid unauthorised detector removal and deviceorientation features for quick easy and secure detector placement.Key FeaturesDual rear cable entry with gland support and ample space forcablesCable gland support to prevent water ingress on 4 sidesDrill location support for cable entry makes installationeasyExternal screw fixtures reduces risk of water ingressDual address tag locations avoids alignment to make tagsvisibleSupports standard Excellence series bases without featureloss all base features remain usableSupports access to the selectable detectorlocking mechanism that protects against unauthorized detector removal

GBP 3.43

1

Kidde 1-23911-K090 FireBeta XT 4 Zone 1 Area Control Panel

Kidde 1-23911-K090 FireBeta XT 4 Zone 1 Area Control PanelKidde 1-23911-K090 FireBeta XT extinguishing control panels are designed and manufactured to the highest standards in a quality controlled environment. With its EN12094-1 approvals it offers outstanding value and performance for small to medium sized fixed firefighting installations. The Kidde 1-23911-K090 FireBeta XT is supplied in an enclosure that matches the design and color of the status unit range.The 4 detection zone circuits allow extinguishing agent release to be configured to activate from any combination of detection zones. This allows among others any 2 zones from the combination of 3 to activate release making it ideal for applications protecting ceiling room and floor voids.The extensive configuration options of the FireBeta XT allow the functionality of the system to be extensively modified to suit the application while still complying with EN12094-1 EN54-2 and EN54-4. A large LED display on the panel fascia enables easy configuration and control. It additionally displays the time remaining until extinguishing agent release for added user safety.The control panel status can be displayed on up to 7 remote status indicators. This allows the agent release status to be displayed at for e.g. multiple entrances to a protected area adding additional user safety. The communication between the panel and its status indicators is fully monitored.The internal electronics are mounted on a single easily removable steel plate making the FireBeta XT robust and easy to install.Key FeaturesWalk test modeTwo first stage sounder outputsOne second stage sounder outputFirst stage relay contactSecond stage relay contactAuxiliary 24V DC outputMonitored manual release inputMonitored extinguishant outputMonitored Released pressure switch inputMode select keyswitch on front panel optionalManual release on front panel optional

GBP 1983.86

1

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display Module

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display ModuleModuLaser is a scalable aspirating smoke detection solution thatmakes installation easier maintenance quicker and takes applicationsfurther than traditional air sampling detectors. Two basic module typescomprise the ModuLaser solution a display module and a detectormodule. Each detector module can accommodate up to 250 meterscombined sampling pipe. Display modules and detector modulescommunicate by RS-485 interconnections.Display modules are available in three configurations Standard withTFT colour display status LEDs and navigation buttons Minimum withonly status LEDs and Command which is similar to the Standard butwith the added functionality to control various modules overSenseNET. The Minimum and Standard Display Modules can eachsupport up to 8 detector modules while the Command Display Modulecan support up to 127 modules across the SenseNET network.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see color TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 487.51

1

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 948.44

1

Kidde AirSense Stratos ModuLaser Detector Module 9-30783

Kidde AirSense Stratos ModuLaser Detector Module 9-30783ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 856.82

1

Kidde AirSense Stratos ModuLaser Command Display Module 9-30782

Kidde AirSense Stratos ModuLaser Command Display Module 9-30782ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.The Standard Display Module features a user interface which consist of a TFT colour display navigation buttons and status LEDs. Configuration of the Standard Display Module and associated detectors modules can be done via the user interface via a computer using Remote software or via SenseNET using a Command Display Module. The TFT colour display support simple operations like changing configuration options via a menu driven structure but also advanced features like viewing the chart recording in graphical format.The Standard Display Module has two USB ports one master and one slave. The master is used to connect a pen drivememory stick which in turn can be used for storing the configuration the event logs or chart recordings or for firmware upgrade purposes. While the USB slave is used to connect to a computer.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 1832.20

1

Kidde AirSense Stratos ModuLaser Standard Display Module 9-30781

Kidde AirSense Stratos ModuLaser Standard Display Module 9-30781ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.The Standard Display Module features a user interface which consist of a TFT colour display navigation buttons and status LEDs. Configuration of the Standard Display Module and associated detectors modules can be done via the user interface via a computer using Remote software or via SenseNET using a Command Display Module. The TFT colour display support simple operations like changing configuration options via a menu driven structure but also advanced features like viewing the chart recording in graphical format.The Standard Display Module has two USB ports one master and one slave. The master is used to connect a pen drivememory stick which in turn can be used for storing the configuration the event logs or chart recordings or for firmware upgrade purposes. While the USB slave is used to connect to a computer.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 1066.99

1

Brand

Merchant

Price (EUR)