16 results (0,14604 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Cooper Bi-Wire Option Board 2 Relay BWOB2Z

Cooper Bi-Wire Option Board 2 Relay BWOB2Z

Cooper Bi-Wire Option Board 2 Relay BWOB2ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 29.59
1

Cooper Bi-Wire Option Board 8 Relay BWOB8Z

Cooper Bi-Wire Option Board 8 Relay BWOB8Z

Cooper Bi-Wire Option Board 8 Relay BWOB8ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 44.39
1

Cooper Bi-Wire Option Board 4 Relay BWOB4Z

Cooper Bi-Wire Option Board 4 Relay BWOB4Z

Cooper Bi-Wire Option Board 4 Relay BWOB4ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 34.52
1

Cooper MCIM Micro Single Channel Input Unit recognised as a input unit

Cooper MCIM Micro Single Channel Input Unit recognised as a input unit

Cooper MCIM Micro Single Channel Input Unit recognised as a input unitAn extensive range of micro interfaces are available to support the Cooper range of control panels providing solutions for most design requirements. The MCIM is a single input soft addressed micro interface incorporating integral short circuit isolators. It is extremely compact and therefore ideal for incorporation into other equipment.The MCIM is fully compatible with the current range of Cooper intelligent addressable fire control panels. It is suitable for monitoring a set of normally open volt free contacts such as sprinkler system flow switches auxiliary panel firefault signals as well as non-fire input signals such as flow valve open contacts generator start up fire door closed etc.FeaturesSoft addressedIntegral short circuit isolatorSingle addressSuitable for monitoring- Flow switches- Non fire inputs- Auxillary panelsUp to 200 units per loopBenefitsQuick and simple to installNo hard addressing required Plug and playCompact sizeProgrammable by Cooper site installer software as technical inputnon fire input

GBP 24.54
1

Cooper CAH330 Intelligent Addressable Multi-Mode Heat Sensor MAH830 FXN725 400003FIRE-0003X

Cooper CAH330 Intelligent Addressable Multi-Mode Heat Sensor MAH830 FXN725 400003FIRE-0003X

Cooper CAH330 Intelligent Addressable Multi-Mode Heat Sensor MAH830 FXN725 400003FIRE-0003XThese ranges of intelligent addressable sensors have been specifically designed to operate with Cooper intelligent addressable fire systems.All sensors are third party approved to the relevant section of EN54 part 7 for smoke detectors part 5 for heat detectors.The heat sensor CAH330 can be set to one of 3 modes 77C 92C and rate of rise. These sensors are designed to be used in environments where the ambient conditions might cause false alarms if smoke detection were to be used for example where there is a high level of dust fumes steam or smoke under normal conditions.Key FeaturesSoft addressedIntegral short circuit isolatorSingle addressWide range of sensor types360 visibility LED using lightpipe technologyDrift compensationRemovable detector chamberAesthetically pleasingBenefitsQuick and simple to installSingle multi-mode heat sensorWide viewing angle for increased LED visibilityCommon mounting basePositive lock indicationDiscreet design for incorporation into any decorEasy to maintainservice

GBP 34.94
1

Cooper MCOM-S Micro Single Channel Output Unit recognised as a sounder

Cooper MCOM-S Micro Single Channel Output Unit recognised as a sounder

Cooper MCOM-S Micro Single Channel Output Unit recognised as a sounderAn extensive range of micro interfaces are available to support the Cooper range of control panels providing solutions for most design requirements.The MCOM is a single output soft addressed micro interface incorporating integral short circuit isolators. It is extremely compact and therefore ideal for incorporation into other equipment.The MCOM is fully compatible with the current range of Cooper intelligent addressable control panels. It is suitable for switching low voltage 24V dc at 1A maximum via a set of non latching relay contacts. It is suitable for switching HVAC control circuits plant shutdown control circuits fire door closure etc.Optional VariantsThe MCOM-R gives a 5 second pulse on reset and is used for connectingresetting beam detectors.The MCOM-S is identified by the panel as a sounder and does not reset on silence resets on reset only.FeaturesSoft addressedIntegral short circuit isolatorSingle addressNon latching changeover relay contactsSuitable for switching low volts control gearOptional variants- MCOM-R- MCOM-SBenefitsQuick and simple to installNo hard addressing required Plug and playCompact size

GBP 31.68
1

Cooper MCOM Micro Single Channel Output Unit recognised as a output unit

Cooper MCOM Micro Single Channel Output Unit recognised as a output unit

Cooper MCOM Micro Single Channel Output Unit recognised as a output unitAn extensive range of micro interfaces are available to support the Cooper range of control panels providing solutions for most design requirements.The MCOM is a single output soft addressed micro interface incorporating integral short circuit isolators. It is extremely compact and therefore ideal for incorporation into other equipment.The MCOM is fully compatible with the current range of Cooper intelligent addressable control panels. It is suitable for switching low voltage 24V dc at 1A maximum via a set of non latching relay contacts. It is suitable for switching HVAC control circuits plant shutdown control circuits fire door closure etc.Optional VariantsThe MCOM-R gives a 5 second pulse on reset and is used for connectingresetting beam detectors.The MCOM-S is identified by the panel as a sounder and does not reset on silence resets on reset only.FeaturesSoft addressedIntegral short circuit isolatorSingle addressNon latching changeover relay contactsSuitable for switching low volts control gearOptional variants- MCOM-R- MCOM-SBenefitsQuick and simple to installNo hard addressing required Plug and playCompact size

GBP 31.68
1

Cooper MCOM-R Micro Single Channel Output Unit 5 second reset pulse

Cooper MCOM-R Micro Single Channel Output Unit 5 second reset pulse

Cooper MCOM-R Micro Single Channel Output Unit 5 second reset pulseAn extensive range of micro interfaces are available to support the Cooper range of control panels providing solutions for most design requirements.The MCOM is a single output soft addressed micro interface incorporating integral short circuit isolators. It is extremely compact and therefore ideal for incorporation into other equipment.The MCOM is fully compatible with the current range of Cooper intelligent addressable control panels. It is suitable for switching low voltage 24V dc at 1A maximum via a set of non latching relay contacts. It is suitable for switching HVAC control circuits plant shutdown control circuits fire door closure etc.Optional VariantsThe MCOM-R gives a 5 second pulse on reset and is used for connectingresetting beam detectors.The MCOM-S is identified by the panel as a sounder and does not reset on silence resets on reset only.FeaturesSoft addressedIntegral short circuit isolatorSingle addressNon latching changeover relay contactsSuitable for switching low volts control gearOptional variants- MCOM-R- MCOM-SBenefitsQuick and simple to installNo hard addressing required Plug and playCompact size

GBP 31.68
1

Cooper CIOP-7273 Addressable Door Release Module

Cooper CIOP-7273 Addressable Door Release Module

Cooper CIOP-7273 Addressable Door Release ModuleThe CIOP-7273 door release module allows addressable systems to comply with the demands of class A doors and their release in the event of the full range of scenarios as detailed in BS7273-4 standard the code of practice governing door holders and door release mechanisms in the UK. The units are 2-way soft addressed output modules that incorporate integral short circuit isolators.They are suitable for switching low voltage 24V DC 2A maximum via a set of non-latching relay contacts. Compatible with the current range of Eaton intelligent addressable control panels their flexibility is further enhanced by the fact that each output can be programmed for the full range of triggers required by BS7273-4 such as disablement fault and fire with additional triggers of pre-alarm fire routing equipment fire protecting equipment. The trigger source can be global by panel by loop by zone or by address. Units can be programmed using Eaton Site Installer software via the RS232 port external power is required for these modules.Please note There is a minimum order quantity of 10 on this product.

GBP 203.24
1

Cooper MAB50R Addressable Reflective Beam Detector 50m Range

Cooper MAB50R Addressable Reflective Beam Detector 50m Range

Cooper MAB50R Addressable Reflective Beam Detector 50m RangeTwo versions of the intelligent addressable loop powered reflective beam detectors are available in this range the MAB50R with a range of up to 50 metres and the MAB100R with a range of 50 to 100 meters. Both the MAB50R and the MAB100R are compatible with Eatons range of intelligent addressable fire systems.These intelligent addressable loops powered reflective beam detectors are extremely simple to install they require no separate power supply operate on a reflective principle and have a simple set up mode to enable easy and quick alignment during installation. These units are designed to replace individual point detectors in large open areas such as warehouses. Fire and fault conditions are signalled to the control panel using standard loop wiring so no additional interconnection required.Key FeaturesLoop poweredSoft addressedIntegral short circuit IsolatorSingle addressReflective beam detectionQuick and simple to setupSaves on both time and installation costsNo power supply requiredSingle device to install instead of numerous point detectorsSingle point of maintenanceWall mounted for ease of maintenance especially in warehouses with rackingKit Contains1 x Detector Head Assembly1 x Prism for the MAB50R1 x Dual Test Filter1 x 4-way Connector for in line wiring1 x 4-way Connector for right angle wiring

GBP 475.60
1

Cooper LP800KIT Loop Tester Kit

Cooper LP800KIT Loop Tester Kit

Cooper LP800KIT Loop Tester KitThe loop tester kit LP800KIT is a hardware software combination that can be used to test commission and fault find a loop of up to 200 intelligent addressable devices sensors sounders ancillary devices without having to connect the loop to Eatons intelligent addressable control panel. The loop tester is connected between the loop and PC.It allows the engineer to quickly identify and locate any loop device that is operating outside its operating conditions by varying the alarm threshold of any loop device alarm pre-alarm and fault.The Loop tester hardware requires a free serial port on the PC either internet or via a USB extension a mains power supply and a direct connection to the device loop.Key FeaturesPre-addressing Identifies all field devices and determines their address and device type.Analogue values Constantly displays in real time the analogue value of all loop devices in order to determine their status.Test LED This command operates the LED of any inputs sensorscall points as well as controls the outputs of sounders and output modules.Device settings Analogue values of all devices can be interpreted according to ranges which can be set and altered by the user OK pre-alarm fire.Event Log A history of events can be stored from the date the application was started.Soft addressing Automatically assigns a new and potentially different address to every device found on the loop.

GBP 623.41
1

Cooper Menvier 400003FIRE-0003X Addressable Multi-Mode Heat Sensor

Cooper Menvier 400003FIRE-0003X Addressable Multi-Mode Heat Sensor

Cooper Menvier 400003FIRE-0003X Addressable Multi-Mode HeatSensorThis range of intelligent addressable sensors have been specificallydesigned to operate with Eatons intelligent addressable fire systems.All sensors are third party approved to the relevant sectionof EN54 part 7 for smoke detectors part 5 for heat detectors and part 17 forshort circuit isolators. The optical sensor CAP320 is suitable for most applicationsgiving the fastest response to slow burning or smouldering fires which giverise to large visible smoke particles.The photo-thermal sensor CAPT340 will respond quickly tofast clean burning fires yet maintain the advantage of optical sensors whendetecting smouldering fires The thermal enhancement of this sensor allows ahigher alarm threshold which provides a greater rejection of false alarms. Thesensor will also raise an alarm at temperatures exceeding 60C.The CAPT340 has daynight modes available programmable fromthe site installer software. The day mode uses the heat aspect of the sensorfor areas which may have smoky environments during for example working hours.The night mode uses a combination of A2S and smoke detection. If notprogrammed the sensor defaults to dual mode.The heat sensor CAH330 can be set to one of 3 modes 77C 92C and rate of rise. These sensors are designed to be used in environmentswhere the ambient conditions might cause false alarms if smoke detection wereto be used for example where there is a high level of dust fumes steam orsmoke under normal conditions.Key FeaturesSoft addressedIntegral short circuit isolatorSingle addressWide range of sensor types360 visibility LED using lightpipe technologyDrift compensation

GBP 34.94
1

Cooper CIOP4 4 Way Mimic Relay Board with 4 Inputs amp 4 Outputs

Cooper CIOP4 4 Way Mimic Relay Board with 4 Inputs amp 4 Outputs

Cooper CIOP4 4 Way Mimic Relay Board with 4 Inputs 4 OutputsThese addressable mimic relay boards CIOP4 and CIOP8 are 4 and 8 way soft addressing output modules incorporating integral short circuit isolators.Both the CIOP4 and the CIOP8 mimic relay boards are fully compatible with the current range of Cooper intelligent addressable control panels. The units are suitable for switching low voltage 24V dc at 1A maximum via a set of non-latching relay contacts.The flexibility of these modules is further enhanced by the fact that each output can be programmed for a range of triggers such as disablement fault fire test panel test zone pre-alarm fire routing equipment fire protecting equipment and reset with up to 16 different trigger sources per output.The trigger source can be global by panel by loop by zone or by address. The logic is available in both OR AND functions.These units have an additional 4 inputs which can initiate a reset silence evacuate and test function.They can be programmed using the CF3000 programmable site installer software and downloaded using the RS232 port.Key FeaturesLoop poweredUnits can be soft or hard addressedIntegral short circuit isolatorSingle address4 input 4 output version4 input 8 output versionPCB version incorporates 4 inputs- Reset- Silence- Evacuate- Test16 settings per outputTrigger types fire fault disablement test prealarm FRE FPE resetTrigger source global by panel by loop by zone by addressLogic functions OR ANDBenefitsQuick and simple to installPluggable terminals for ease of wiringProgrammable via site installer softwareCost effective installation solution

GBP 372.41
1

Cooper CIOP8 8 Way Mimic Relay Board with 4 Inputs amp 8 Outputs

Cooper CIOP8 8 Way Mimic Relay Board with 4 Inputs amp 8 Outputs

Cooper CIOP8 8 Way Mimic Relay Board with 4 Inputs 8 OutputsThese addressable mimic relay boards CIOP4 and CIOP8 are 4 and 8 way soft addressing output modules incorporating integral short circuit isolators.Both the CIOP4 and the CIOP8 mimic relay boards are fully compatible with the current range of Cooper intelligent addressable control panels. The units are suitable for switching low voltage 24V dc at 1A maximum via a set of non-latching relay contacts.The flexibility of these modules is further enhanced by the fact that each output can be programmed for a range of triggers such as disablement fault fire test panel test zone pre-alarm fire routing equipment fire protecting equipment and reset with up to 16 different trigger sources per output.The trigger source can be global by panel by loop by zone or by address. The logic is available in both OR AND functions.These units have an additional 4 inputs which can initiate a reset silence evacuate and test function.They can be programmed using the CF3000 programmable site installer software and downloaded using the RS232 port.Key FeaturesLoop poweredUnits can be soft or hard addressedIntegral short circuit isolatorSingle address4 input 4 output version4 input 8 output versionPCB version incorporates 4 inputs- Reset- Silence- Evacuate- Test16 settings per outputTrigger types fire fault disablement test prealarm FRE FPE resetTrigger source global by panel by loop by zone by addressLogic functions OR ANDBenefitsQuick and simple to installPluggable terminals for ease of wiringProgrammable via site installer softwareCost effective installation solution

GBP 380.40
1

Cooper Menvier 400002FIRE-0002X Addressable Optical Smoke Sensor

Cooper Menvier 400002FIRE-0002X Addressable Optical Smoke Sensor

Cooper Menvier 400002FIRE-0002X Addressable Optical SmokeSensorThis range of intelligent addressable sensors have been specificallydesigned to operate with Eatons intelligent addressable fire systems.All sensors are third party approved to the relevant sectionof EN54 part 7 for smoke detectors part 5 for heat detectors and part 17 forshort circuit isolators. The optical sensor CAP320 is suitable for most applicationsgiving the fastest response to slow burning or smouldering fires which giverise to large visible smoke particles.The photo-thermal sensor CAPT340 will respond quickly tofast clean burning fires yet maintain the advantage of optical sensors whendetecting smouldering fires The thermal enhancement of this sensor allows ahigher alarm threshold which provides a greater rejection of false alarms. Thesensor will also raise an alarm at temperatures exceeding 60C.The CAPT340 has daynight modes available programmable fromthe site installer software. The day mode uses the heat aspect of the sensorfor areas which may have smoky environments during for example working hours.The night mode uses a combination of A2S and smoke detection. If notprogrammed the sensor defaults to dual mode.The heat sensor CAH330 can be set to one of 3 modes 77C 92C and rate of rise. These sensors are designed to be used in environmentswhere the ambient conditions might cause false alarms if smoke detection wereto be used for example where there is a high level of dust fumes steam orsmoke under normal conditions.Key FeaturesSoft addressedIntegral short circuit isolatorSingle addressWide range of sensor types360 visibility LED using lightpipe technologyDrift compensationAesthetically pleasingQuick and simple to installSingle multi-mode heat sensorWide viewing angle for increased LED visibilityCommon mounting basePositive lock indicationDiscreet design for incorporation into any dcorEasy to maintainservice

GBP 34.98
1

Cooper Menvier 400004FIRE-0004X Addressable Photo-Thermal Sensor

Cooper Menvier 400004FIRE-0004X Addressable Photo-Thermal Sensor

Cooper Menvier 400004FIRE-0004X Addressable Photo-ThermalSensor This range of intelligent addressable sensors have been specificallydesigned to operate with Eatons intelligent addressable fire systems.All sensors are third party approved to the relevant sectionof EN54 part 7 for smoke detectors part 5 for heat detectors and part 17 forshort circuit isolators. The optical sensor CAP320 is suitable for most applicationsgiving the fastest response to slow burning or smouldering fires which giverise to large visible smoke particles.The photo-thermal sensor CAPT340 will respond quickly tofast clean burning fires yet maintain the advantage of optical sensors whendetecting smouldering fires The thermal enhancement of this sensor allows ahigher alarm threshold which provides a greater rejection of false alarms. Thesensor will also raise an alarm at temperatures exceeding 60C.The CAPT340 has daynight modes available programmable fromthe site installer software. The day mode uses the heat aspect of the sensorfor areas which may have smoky environments during for example working hours.The night mode uses a combination of A2S and smoke detection. If notprogrammed the sensor defaults to dual mode.The heat sensor CAH330 can be set to one of 3 modes 77C 92C and rate of rise. These sensors are designed to be used in environmentswhere the ambient conditions might cause false alarms if smoke detection wereto be used for example where there is a high level of dust fumes steam orsmoke under normal conditions.Key FeaturesSoft addressedIntegral short circuit isolatorSingle addressWide range of sensor types360 visibility LED using lightpipe technologyDrift compensationAesthetically pleasingQuick and simple to installSingle multi-mode heat sensorWide viewing angle for increased LED visibilityCommon mounting basePositive lock indicationDiscreet design for incorporation into any dcorEasy to maintainservice

GBP 42.90
1